SimAirport Cheat Codes - Trainers City - Cheats & Soluces -




Name of the file: SimAirport Cheat Codes - Author: DAV

Cheat Codes:
------------
Submitted by: David K.

Creating and Using Standby Gates:
---------------------------------
Written by ajax_post

A simple guide to creating and using Standby Gates in SimAirport.

-=Why Use A Standby Gate?=-
If you have a very busy airport and your flight schedule is very tightly packed
you run the risk of a flight boarding at one gate not departing before the next
flight using that gate arrives.

Incoming flights usually arrive early, often quite a bit earlier than you have
scheduled for. This is good because it means your staff, the crew, and passengers
have a little more time before the aircraft has to depart. But if there is any
delay with the preceding flight then it can cause the subsequent flights to
run late causing problems such as dissatisfaction and lose of the 'perfect ops'
bonus.

One way of avoiding these sort of crushes at the gate is to make one (or more
gates) available as a 'standby' so that if a gate is still in use when the next
flight arrives that incoming aircraft can be diverted to the 'standby' gate
where the incoming passengers can disembark, those departing can board and the
flight can leave again without incurring a delay penalty.

Research The Operation
Research Standby Gates

Before you can build or assign a Standby Gate the facility must be researched.

This is in the 'Operations' section and you must already have a COO employed and
in an office.

It's not an expensive research option and only takes 12 hours to complete so you
can start using Standby Gates quite early in the development of your airport if
you want to get as many flight contracts as possible.

-=Build The Gate=-
A Standby Gate Is Just A Gate

A Standby Gate is just the same as any other gate in your airport except that it
will have fewer, if any, flights scheduled. You do not need to wait until you
have completed the research before building the gate as any existing gate can be
assigned Standby operation.

Like any other gate you will need to:

* Assign and schedule Gate Agents
* Connect it to the baggage handling system (if you have one)
* Connect it to your fuel delivery infrastructure (if you have one)
* If you have a PA system assign it to one (or more?) of the amplifiers

Basically, just set up a Standby Gate in exactly the same way you would a normal
gate.

Schedule Standby Operation
Add Standby To Your Schedule

When you have complete the 'Standby Gates' research a new option will be available
on the Flight Management screen which allows you to add and remove standby operation
on any gate.

On the right-hand side in the middle of the dialog box the "Schedule Edit Mode"
will now allow you to choose between 'Flights' and 'Standby'. Select 'Standby Gates'
to schedule the standby period(s).

Typically you will use a gate with no scheduled flights but that is not actually
necessary. Left-click within the gate row at the time you want to start (or end)
the period of standby operation. Then drag either right or left to extend the
period. A white block will be added to the gate's schedule When you release the
mouse button it will be titled 'Standby'.

You can create a single or multiple periods of standby operation. Simply left-click
and drag to either extend any existing standby block or create a new period.

If there are times when your timetable is not too busy and a Standby Gate is not
necessary you can add scheduled flights to the same gate.

Remember: Select the "Schedule Edit Mode" 'Flights' to add contracted flights and
'Standby Gates' to edit the standby operation periods.

Remove Standby Operation
Removing Standby Periods

If you decide that you do not need a particular period of standby operation, or
wish to remove standby operation from a gate entirely, simply select 'Standby
Gates' from the "Schedule Edit Mode" drop-down.

To remove a single specific period of standby right-click on the unwanted block
of standby time and select 'Remove'.

To remove all standby on a gate right-click anywhere on the gate row select
'Clear Row'.

Note that the 'Clear Row' option only removes standby periods it does not remove
any scheduled flights on that same gate.



Copyright (c) 1998 - 2024 - Trainers City - The Trainers Bible - All Rights Reserved - back